Centralina Aggiuntiva Ford

Chip tuning car includes adjustments that enhance the execution, the care of, and presentation of a vehicle. Tuning is an approach to customize a car and is a side interest for some. The territories of adjustment incorporate sound, inside, motor, suspension, and body. Every one of these ranges makes an interminable number of particular auto adjustments and can incorporate expanding efficiency, enhancing taking care of, or changing the outside.

The ECU response will continue to correspond to lower octane even though you have started using higher-octane fuel. This is because the ECU has not been reset for higher octane. Thus even though higher octane is in actual use, the data in ECU memory still corresponds to that of lower octane. This mismatch affects performance, as you are unable to derive the benefits of boosting the octane. Therefore you should reset your ECU periodically after filling up full tank in order to ensure that ECU adjustments for its octane memory are made afresh corresponding to the octane actually in use. You can even customize resetting of your ECU so as to enable it to adapt itself to seasonal changes. Since humidity, air density, oxygen levels etc in air affect performance you could reset the ECU to adapt to these variables too.

Opinions on tuning box? Chip replacements were the only way to change a cars mapping but now with standardised diagnostic ports it is much easier. In recent times we have seen cars equipped with on board diagnostic ports that allow a fresh map to be uploaded. Is chip tuning something you can easily do yourself? Not really, you need to have detailed knowledge of the engine and ideally a full set of diagnostic equipment on a rolling road to allow you to make “live” adjustments to the mapping. There is certainly a lot more to it than just changing a few numbers and getting a big power gain. With DIY chip tuning you also run the risk of a bad flash where the computer cannot be recovered and without a restoration image you will need to visit the main dealer or worse still buy a new computer. Discover extra info at Chip Tuning Hyundai.

The procedure of chip tuning: The chip tuning is performed in several steps. Upon receiving the vehicle, we read out the error memory. This ensures that the vehicle has not stored any electronic errors in the memory. This is followed by a visual inspection in the engine compartment to rule out any leaks in the boost system or any other defects. If the vehicle is functioning properly, we read out the original software of the engine control unit and save it. Then we optimize the parameters in the special maps. Once the programming has been completed, we flash the optimized data onto the engine control unit. A test drive follows during which all parameters are monitored and read out live. If a value is at variance, it will be adjusted again in the software and flashed once more onto the control unit. Once all values are in the optimal range, the programming is completed, and you can enjoy your performance boost!

Warranties: Directly related to the above point, having your engine chip tuned can cause problems for any warranties you may hold on your vehicle or engine. However, this largely depends on the manufacturer and model of car and whether or not you get the process done with an accredited mechanic. This is because the limits that the manufacturer has placed on the engine are designed to ensure a safe driving experience that won’t damage the engine. Check your owner’s manual or call a mechanic or dealership to find out if tuning your engine chip could pose any problems.

OEM clutch – for VW 2.0TDi 103kW engine – is designed for 400Nm torque. VW Q02 six-speed gearbox is rated for max. 500Nm. Factory engine calibration data allow 320Nm @ 1800-2500rpm. Bad standard remap can easily go over 400Nm right from 1800rpm. What do you think happen to OEM dual-mass clutch? It reminds me few years ago…we replaced friend’s clutch after one bad ECU remap combined with bad driver mentioned earlier. All piston heads love motorsport…we all watched Walter Roehrl, Ari Vatanen, Stig Blomqvist, Juha Kankunnen, Colin McRae, Ayrton Senna or Schumi…did you also noticed they never used low revs, rarely used mid range revs and most of time spent in high revs where optimal power and torque is. One wonders why so many drivers try to push it hard in low revs and chiptuners support this stupidity. Power = Torque x RPM. More engine revs less torque you need. Why do you need 96HP@380Nm@1800rpm if you can have 170HP@3500rpm where is the optimal place to shift gears. Read more info at Chiptuning Subaru.